Al Bundy
03-10-2009, 04:13 PM
C/P
How To Recover 360 Premier
--------------------------------------------------------------------------------
If your reciever is newer than Oct 31 2008.
Goto File section get the factory file. (SV360_Premier_Factory_V0105.zip)
Delete all the files on your USB thumbdrive.
Don't format the USB drive
Unzip the file on the hard drive and load it ONLY on the USB drive.
Release the USB drive properly from the PC.
Turn the receiver off from the rear.
Disconnect the cable from the sat
Plug in the USB Drive in the front slot of the receiver
Turn on the receiver while holding the ok button on the front in.
Let go after you see the boot load display screen.
push ok to select the file via the front panel button.
Load the file
wait about 5 min...its hard to tell if it loads.
Turn the unit off from the rear.
Count to 30
Turn it back on and see if it boots normally.. if it does...turn it off..attach the cable to the top connector and turn it back on.
Go back to the PC and add the latest file for the receiver.
Take it to the receiver and load it via the on screen PVR menu with the remote.
Do your settings and feature setup.
Do your scan individually by sat no Blind scans.
You should be good to go from there.
If your reciever is older than Oct 1 2008.
Goto File section get the 119 SYS file and the sat file
Don't use the clean sys file.
Delete all the files on your USB thumbdrive.
Don't format the USB drive
Unzip the files on the hard drive and load both on the USB drive.
Release the USB drive properly from the PC.
Turn the receiver off from the rear.
Disconnect the cable from the sat
Plug in the USB Drive in the front slot of the receiver
Turn on the receiver while holding the ok button on the front in.
Let go after you see the boot load display screen.
select the 119 SYS file via the front panel button. push ok
Load the file
wait about 3 min
select the sat file via the front panel button. push ok
wait about 5 min...its hard to tell if it loads.
Turn the unit off from the rear.
Count to 30
Turn it back on and see if it boots normally.. if it does...turn it off..attach the cable to the top connector and turn it back on.
Go back to the PC and add the latest file for the receiver.
Take it to the receiver and load it via the on screen PVR menu with the remote.
Do your settings and feature setup.
Do your scan individually by sat no Blind scans.
You should be good to go from there.
How To Recover 360 Premier
--------------------------------------------------------------------------------
If your reciever is newer than Oct 31 2008.
Goto File section get the factory file. (SV360_Premier_Factory_V0105.zip)
Delete all the files on your USB thumbdrive.
Don't format the USB drive
Unzip the file on the hard drive and load it ONLY on the USB drive.
Release the USB drive properly from the PC.
Turn the receiver off from the rear.
Disconnect the cable from the sat
Plug in the USB Drive in the front slot of the receiver
Turn on the receiver while holding the ok button on the front in.
Let go after you see the boot load display screen.
push ok to select the file via the front panel button.
Load the file
wait about 5 min...its hard to tell if it loads.
Turn the unit off from the rear.
Count to 30
Turn it back on and see if it boots normally.. if it does...turn it off..attach the cable to the top connector and turn it back on.
Go back to the PC and add the latest file for the receiver.
Take it to the receiver and load it via the on screen PVR menu with the remote.
Do your settings and feature setup.
Do your scan individually by sat no Blind scans.
You should be good to go from there.
If your reciever is older than Oct 1 2008.
Goto File section get the 119 SYS file and the sat file
Don't use the clean sys file.
Delete all the files on your USB thumbdrive.
Don't format the USB drive
Unzip the files on the hard drive and load both on the USB drive.
Release the USB drive properly from the PC.
Turn the receiver off from the rear.
Disconnect the cable from the sat
Plug in the USB Drive in the front slot of the receiver
Turn on the receiver while holding the ok button on the front in.
Let go after you see the boot load display screen.
select the 119 SYS file via the front panel button. push ok
Load the file
wait about 3 min
select the sat file via the front panel button. push ok
wait about 5 min...its hard to tell if it loads.
Turn the unit off from the rear.
Count to 30
Turn it back on and see if it boots normally.. if it does...turn it off..attach the cable to the top connector and turn it back on.
Go back to the PC and add the latest file for the receiver.
Take it to the receiver and load it via the on screen PVR menu with the remote.
Do your settings and feature setup.
Do your scan individually by sat no Blind scans.
You should be good to go from there.