Centauri
09-18-2007, 03:06 PM
How to update with current bin using CS Upgrade loader V3.01 for proper auto-roll
BEFORE YOU BEGIN…
1) Just make sure each of the required files below must be unzipped
2) You must know where the unzipped files are located preferably a separate folder
3) You must Factory Reset the receive before you begin the following
4) Turn the receiver off from the back power switch after the factory reset.
5) Connect the null (RS232) cable to your PC and the Receiver
6) Disconnect receiver from the satellite feeding cable
THE LOADER
Open the loader; New loader CSUpgrade_v3.01.exe
http://www.dssgeeks.com/forums/loader-cs-8100hd-t9891/index.html
NOTE: Depending on your operating system (Windows 98, 2000, XP and Vista) you may need following three OCX files in the same directory where CSUpgrade_v3.01 is located and ALSO under C:\Windows\System32.
1) COMCTL32.OCX
2) COMDLG32.OCX
3) MSCOMM32.OCX
How to apply the OCX file: Copy and paste the following command into command window (by typing ‘cmd’ on run) Copy the command line below (one line at a time) and paste in command window by clicking the “right mouse button” and press enter
REGSVR32 C:\WINDOWS\SYSTEM32\COMCTL32.OCX
REGSVR32 C:\WINDOWS\SYSTEM32\COMDLG32.OCX
REGSVR32 C:\WINDOWS\SYSTEM32\MSCOMM32.OCX
FIRST STEP LOADING THE CLEAR_SW_HD.BIN FILE…
http://www.dssgeeks.com/forums/cs8000hd-clean-software-t13712/index.html
Once the loader is up and running, do not change any selection, simply click on “Browse” to locate and select the unzipped file Clear_SW_HD.bin. Upon selection you will see the file in the window, click "Start" and also turn the receiver ON from the back and wait for the file to download and complete. This will take 3-5 minutes. Once completed, turn the receiver OFF from the back and click OK on the completed pop-up.
SECOND STEP LOADING THE FACTORY FLASH…
http://www.dssgeeks.com/forums/cs-8100-factory-t9888/index.html
Using the same loader program, do not change any selection, simply click on “Browse” to locate and select the unzipped file original Factory Flash -11170A.sgn. Upon selection you will see the file in the window, click "Start" and also turn the receiver ON from the back and wait for the file to download and complete. This will take 3-5 minutes. Once completed, turn the receiver OFF from the back and click OK on the completed pop-up
LAST STEP LOADING THE LATEST BIN…FOUND BELOW THE BLUE STICKIES
http://www.dssgeeks.com/forums/coolsat-8100hd-files-f248/index.html
Using the same loader program, do not change any selection, simply click on “Browse” to locate and select the unzipped copy of current file e.g. 11175F.sgn. Upon selection you will see the file in the window, click "Start" and also turn the receiver ON from the back and wait for the file to download and complete. This will take 3-5 minutes. Once completed, turn the receiver OFF from the back and click OK on the completed pop-up
BEFORE YOU END…
1) Unplug the null cable from the back of the receiver and PC
2) Hook the receiver back up to the satellite cable.
3) Power up the receiver from the back
4) Let it auto-scan or scan as per your setup
5) Make sure that the auto-roll is ON and your settings are correct.
6) WAIT for the receiver to perform auto roll
7) Enjoy the TV
ACKNOWLEDGEMENT: Thanks to FurFace and many others for their ideas and suggestions…
BEFORE YOU BEGIN…
1) Just make sure each of the required files below must be unzipped
2) You must know where the unzipped files are located preferably a separate folder
3) You must Factory Reset the receive before you begin the following
4) Turn the receiver off from the back power switch after the factory reset.
5) Connect the null (RS232) cable to your PC and the Receiver
6) Disconnect receiver from the satellite feeding cable
THE LOADER
Open the loader; New loader CSUpgrade_v3.01.exe
http://www.dssgeeks.com/forums/loader-cs-8100hd-t9891/index.html
NOTE: Depending on your operating system (Windows 98, 2000, XP and Vista) you may need following three OCX files in the same directory where CSUpgrade_v3.01 is located and ALSO under C:\Windows\System32.
1) COMCTL32.OCX
2) COMDLG32.OCX
3) MSCOMM32.OCX
How to apply the OCX file: Copy and paste the following command into command window (by typing ‘cmd’ on run) Copy the command line below (one line at a time) and paste in command window by clicking the “right mouse button” and press enter
REGSVR32 C:\WINDOWS\SYSTEM32\COMCTL32.OCX
REGSVR32 C:\WINDOWS\SYSTEM32\COMDLG32.OCX
REGSVR32 C:\WINDOWS\SYSTEM32\MSCOMM32.OCX
FIRST STEP LOADING THE CLEAR_SW_HD.BIN FILE…
http://www.dssgeeks.com/forums/cs8000hd-clean-software-t13712/index.html
Once the loader is up and running, do not change any selection, simply click on “Browse” to locate and select the unzipped file Clear_SW_HD.bin. Upon selection you will see the file in the window, click "Start" and also turn the receiver ON from the back and wait for the file to download and complete. This will take 3-5 minutes. Once completed, turn the receiver OFF from the back and click OK on the completed pop-up.
SECOND STEP LOADING THE FACTORY FLASH…
http://www.dssgeeks.com/forums/cs-8100-factory-t9888/index.html
Using the same loader program, do not change any selection, simply click on “Browse” to locate and select the unzipped file original Factory Flash -11170A.sgn. Upon selection you will see the file in the window, click "Start" and also turn the receiver ON from the back and wait for the file to download and complete. This will take 3-5 minutes. Once completed, turn the receiver OFF from the back and click OK on the completed pop-up
LAST STEP LOADING THE LATEST BIN…FOUND BELOW THE BLUE STICKIES
http://www.dssgeeks.com/forums/coolsat-8100hd-files-f248/index.html
Using the same loader program, do not change any selection, simply click on “Browse” to locate and select the unzipped copy of current file e.g. 11175F.sgn. Upon selection you will see the file in the window, click "Start" and also turn the receiver ON from the back and wait for the file to download and complete. This will take 3-5 minutes. Once completed, turn the receiver OFF from the back and click OK on the completed pop-up
BEFORE YOU END…
1) Unplug the null cable from the back of the receiver and PC
2) Hook the receiver back up to the satellite cable.
3) Power up the receiver from the back
4) Let it auto-scan or scan as per your setup
5) Make sure that the auto-roll is ON and your settings are correct.
6) WAIT for the receiver to perform auto roll
7) Enjoy the TV
ACKNOWLEDGEMENT: Thanks to FurFace and many others for their ideas and suggestions…